First, one method is to use ready-made design patterns to transfer. When drawing on paper, remember that when it is tapped on the skin, it is reversed. Turn it over and place it under the light. This is what you want to show on your skin. If you want the direction of the tattoo to be consistent with the design pattern, the design must be reversed or reversed.
Brush (transfer pen)
This is a very simple but very effective transfer method. The required materials are a design drawing, an offset pencil or a pen with offset color, and a piece of high-quality copy paper (or translucent sulfuric acid paper). The copy paper is very thin and the transparency is also very good, which is conducive to see the design diagram below through it. First, glue the pattern (face up or upside down) to the drawing board or clip it to the clipboard with a clip, and then glue or clip the copy paper to it. This paper should have a large enough area for drawing the design drawings. After confirming that the entire pattern is covered, use an economical placement method (like in the corner of the paper instead of the middle, so that you can save space and use the part under the copy paper to draw other designs. You can see that pattern through the copy paper. No, just put a small desk lamp next to the drawing board so that you can see clearly. This requires the drawing board to be transparent, or a transparent table specially used for copying patterns can be made. This kind of table with light inside will work Brings us great convenience.
Take a paintbrush and copy the design on paper, and trace it carefully according to the outline of the tattoo design. Sometimes it takes several iterations to draw a three-dimensional line. Then cut out the tracing pattern. Pay attention to leaving a distance of at least 2 cm wide around the pattern. In this way, you have completed the production of the entire template. How to put this template on the skin? The best way is to stick it with ordinary transfer paste. After you have determined the tattoo, apply alcohol to the tattooed area for disinfection, and then shave the hair at this position (not to let go of every subtle place). Next, apply a thin layer of transfer paste on the skin, and place the finished pattern paper on top of it. Rub your finger for a few seconds, then remove the paper. Look at the patterns on the skin. Check the accuracy and let the customer check it too. Of course, there are certain skills to complete the transfer neatly, so a lot of practice is needed on the tattooed part. It is easy to practice the transfer technique on the tattooed person because it can be washed off and tried again and again. Your friend, wife, husband or yourself are all good models to practice.
Transfer ink and pen
This method is exactly the same as the transfer pen technology, but instead of using an offset brush, a large feather pen and a bottle of color material are used. It is better than the transfer pen in some aspects. First of all, the transfer color line is very three-dimensional on carbon paper, it cannot be copied, and the template can be used multiple times. If you are careful not to abuse it during the transfer process, the brush template can also be used again.
Use, but the pigment will not last long, and can be used up to 6 times. The transfer color material works well on copy paper and is easy to transfer. The only disadvantage is that it is difficult to find the transfer colorant, and this colorant only comes from a company called the United States. The process of applying the template is the same as the brush template.
Identical copy (copy)
This will usually give you the same results as the brush or color method, but a different method. The materials needed are design drawings, ballpoint pens (or similar) or a piece of transfer paper. To start copying the pattern, trace it line by line with a ballpoint pen. When you are done, lift up the copy and look at it, and the pattern is printed on the next sheet of paper. This is the template. It can be trimmed, and then applied to the skin with a transfer paste.
Skin marker
Markers are often called skin liners or surgical pens. The marker used in surgery is a tool used by doctors to draw anatomical lines for patients. The skin marker is non-toxic and is specially designed for marking on the skin. It is not very good to just practice drawing patterns on the body because mistakes and changes often occur. It is better to redraw it on paper beforehand, and then transfer it in another way. The skin liner is a retouching tool that can change or add patterns already drawn on the body. For this purpose, a few surgical pens should generally be prepared on hand, which can be used at any time when needed.
One of the most popular methods of pattern transfer is to use acetate stencils. Acetate flakes (called transfer paper in China) can be obtained from suppliers. There are two specifications, scroll or single page, which is about 0.02 inches thick. The most practical way is to calculate the material with the reel so that you can cut the size you need. This kind of transfer paper can be used to copy the pattern with a thermal transfer machine or put the pattern on the transfer paper and trace it down like carbon paper, so that we get the required pattern template.
When the stencil made by transfer paper is applied to the skin with transfer paste, try to press it tightly with your fingers and hold it all over it.
The next trick is to quickly remove it from the skin, remember not to pull it away slowly, this will leave a clear pattern. If it doesn't look very clear, just wash it off and try again. But it should do well for your customers once. You can do a lot of practice on yourself beforehand to get familiar with this technique. Only when you can transfer patterns well every time, can you become a professional tattoo artist.
If you have a good electrostatic photocopier on hand, it can usually reproduce the tattoo design pattern completely on the skin, or even reproduce the photo on the skin. This allows you to grasp the similarity of the works well when getting portrait tattoos. However, the toner in some electrostatic printers is harmful to the human body, and it is very unsafe to use some non-standard chemical and chemical products when transferring. The pattern of the electrostatic copier is often mirrored (that is, the direction of the pattern is opposite), so this method should be used with caution.
All the methods in this article are effective and you should try each one. The selection method depends on the environment. It should be emphasized that those who are new to tattoos should practice making templates and transferring them until they are very proficient. For tattoos, the template is very important, because a clean template will make the tattoo easy to complete, and a dirty template will cause a lot of trouble. Perfect template making is a basic requirement for professional tattoos.
