Introduction of the working principle of tattoo machine and selection of tattoo needle
The Chongqing tattoo machine converts the externally connected 220V AC power into DC voltage with a voltage value between 3-20V through the intermediate voltage regulator and transformer. Under the DC voltage of 3-20V, an instant occurs between the two main coils and the EFI point The suction and spraying effect of the tattoo machine drives the tattoo needle to produce high-speed up and down and reciprocating motion by the reciprocating motion of the spring leaf of the tattoo machine. One of the biggest benefits of this working method is that it can generate high speed and large torque because it is not driven by the motor or motor and does not need to take into account the power consumption of the motor or motor. When working, the tattoo needle punctures the epidermis layer at a high speed and evenly. The striated pigment is implanted into the base layer of the epidermis layer to allow the pigment to be permanently fixed to the epidermis, forming exquisite patterns and texts of various pigment combinations, to modify the skin and cover the scars .
The origin of the tattoo machine, the early tattoo was called tattoo, because it was a manual monochrome piercing operation at the time, and the pattern color was restored to be mostly blue, so it was named tattoo, which was invented by Sam O'Reilly in 1892. Since then, modern tattoos have developed rapidly, with only a slight pain, and their speed is fast, simple tattoos are just a few minutes.
Early tattoo machine equipment was rough, mostly hand-made, and the cost of manual manufacturing was high. The pattern was single. At that time, the electric tattoo machine beat 1000 times per minute, only stabbing the epidermis of the skin, and the depth was only 0.8-1 mm. Today, the manufacture of tattoo machines has reached the point of perfection. Electric tattoo machines beat 30,000 times per minute. Mass production and processing have made tattoo machines cheap, and the number of practitioners of tattooists around the world has also increased.
There are two types of tattoo machines, one is a double machine, and the other is a fit machine. The so-called double machine is a secant machine and a fog machine. The two have different divisions of labor and different performance. The fitting machine is a machine. When cutting and fogging, you need to manually adjust the frequency of the machine or the size of the power supply to control the operating speed and needle out of the machine to cut and fog.
A good tattoo machine is not about the price, but the structure of the machine, such as the materials used, the number of coils, the length of the hanging iron, the hardness of the shrapnel, and the feel of the machine. The following Jiulongtang will give you a brief explanation. !
The average machine can judge whether the machine is good or bad by listening to the sound. It does not emit sparks and the sound is crisp. You can pass the level of the machine by listening. Here, according to experience, large capacitors are better than small capacitors. , But it is divided into machines! It is best to debug on site when buying a machine!
Some friends say that their machine gets hot in less than 10 minutes. Please check to see if the needle bar is rubbed and straight when the machine is in operation. The normal needle should be in the middle of the straight line and the straight line should not touch the straight line. Control by adjusting the hanging iron length and shrapnel!
The coil size of the thread machine is different, the fog is bigger!
In the case of hanging iron, the length of the hanging iron determines whether the needle can bounce unimpeded without contacting the straight-through, but some machines have a short hanging iron, which can be extended by adjusting the shrapnel, but when the shrapnel is extended, The shrapnel is very demanding. The hard shrapnel has a bad effect after being extended. The soft shrapnel does not produce good results. Only qualified shrapnel is the best! The number of needles is proportional to the speed frequency. The smaller the number of needles, the slower the speed adjustment, otherwise, the faster the speed, of course, this depends on different needs. In addition, the appearance of color is not only related to the number of needles but also the depth of penetration into the skin. The tattoo machine can make appropriate adjustments in the softness of the contact between the shrapnel and the electromagnetic coil, and can also make appropriate adjustments in the pigment concentration. dilution. From this direction, we can derive another important key to the penetration of the needle into the skin-the distribution of needle points.
In terms of completing a color block with thorns, the best theoretical phenomenon is the uniform distribution of the needle points, that is, this color block is a large color block that is composed of many small needle points. When a small wound is formed, it will naturally cause less damage to the skin. Since the abrasion is the destruction of the entire skin surface, we must think of how to achieve this effect, so we should understand when the tattoo machine penetrates the skin. What is the relationship between the frequency of needle withdrawal and the speed of hand movement?
Suppose that the tattoo machine draws out the needle ten times in a second, and if the skin pierced at the same point does not move, it will prick ten times at the same point and form a large point. If the hand moves in a straight line at a speed, It will form ten points arranged in a line, and the interval between points will move faster and faster with the hand, and the slower the smaller, until the points and points are closely connected to form a continuous line, which is the needle Another important key to pierce the skin. We can know the frequency of the needle and the speed of the hand movement. The needs vary according to the needs of the graphics and match each other. Only need to know this basic principle, we can better understand how to adjust from the effect of the thorn. Correct my pace. In addition to cutting the tattoo machine, every time it touches the skin and touches the skin, unless it is necessary, it can not be stopped at the same place, so there will be a moving movement from front to back, left, right, or rotating from time to time. ? Some beginners of tattoos often ask whether it is better to move back and forth, left or right, or to draw a circle. If we understand the relationship between the frequency of the needle and the speed of the hand movement, we will understand that this problem is not absolute. The brush strokes are not the same, as long as you can evenly distribute the needle points, which method is not the focus, because all methods are used by tattoo artists, it should be a personal habit.
The overall material of the tattoo machine is cast iron. The personal experience is that stainless steel is not suitable for tattoo machines, and other materials are not suitable. Only cast iron is the most suitable for the most tattoo machine. As for why I ca n’t tell, there are many machines with smooth appearance. , Color, it means stainless steel or other materials, in fact, all of it is cast iron, but after finishing, deep processing, smoothing and plating processing, showing color and smoothing effect. The coil of the fog machine is 10 turns and the cutting line is 8 turns. Of course, it is almost invisible from the appearance, but some fog and cut.
